item8
item8
TANK LEVEL ALARM
IBC ALARM - LOW LEVEL

The IBC TANK LEVEL ALARM is supplied with a cap to fit an intermediate bulk container. (tote tank) Liquid is fed to your process through a tube and flowmeter. When liquid level gets low, a bright flashing LED and a loud beeper alerts. Never run empty again!

IMG0802

MODEL ILP-PP

IBC TANK LEVEL ALARM

Better Liquid Level Control...

  • Always on duty because the liquid tube is permanently attached to the alarm unit.
  • It can go anywhere because its battery powered. No need for power outlets.
  • Uninterruptible battery power lasts for years. Lithium battery included.
  • Loud warbling tone cuts through the loudest industrial noise.
  • Rugged. Built for rough, wet and corrosive environments.
  • Protects your pumps from debris with an intake screen.
  • Flow indicator built into low level units.
  • No wetted metal parts.

IBC TOTE TANK ALARM for low liquid level makes sure your process will never run out of chemicals. When liquid level is low, an IBC Alarm emits a very loud 103dB beeping sound, and flashing LED.

IMG0130

PVDF - ILPX-KY

IMG0647

NO FEED PIPE - ILK-PP

IMG0512

Uninterruptible battery power works through power failures, can't come unplugged, or be defeated. And, because the Drum Alarms don't use any power until alarming, the batteries last for years.

Float switch is protected inside a pipe. The float is immune to abuse from getting knocked around during transfer between containers. Years of reliable service.

Adjustable depth to fit any size tote tank. Simply loosen the set screws to slide pipes to correct depth up to 50 inches. (this is slightly deeper than a standard 330 gallons Mauser IBC tank which is 48.5")

The feed tube is permanently attached to the float switch, so the level alarm is always on duty.

Removable filter screen on the suction pipe guards your pumps from debris or crystals. A replaceable check valve can be easily inserted in-line to prevent liquid from draining when transferring to new containers if needed.

Different materials for different chemistries: polypropylene is standard and PVDF and stainless steel by request.

Polypropylene models have polypropylene floats, and polypropyelene piping so all wetted parts are polypropylene except the Acrylic flow indicator and glass ball. If Acrylic is incompatible there are models available without the flow indicator.

 

Standard Models Available

ILP-PP - polypropylene wetted parts with liquid suction pipe and acrylic flowmeter. Includes 6 inch buttress thread lid.

ILPX-PP - same as above but no flow indicator

ILK-PP - no liquid suction pipe. (level alarm part only)

PVDF (Kynar) models have the suffix KY instead of PP.

Other options below can be added on but don't change the base model number.

Sealmoneyback1
We want only happy customers.
click

PayPal Logo

VeraSafe Security Seal

SPECIFICATIONS

GENERAL

  • Maximum working depth.................................. 50 inches
  • Total depth including electronics enclosure......56 inches
  • PVC enclosure rating ............................ NEMA4X / IP65
  • Buzzer volume.............................................103dB @ 2ft
  • Current during alarm...............................................30mA
  • Lid (IBC lid crawing) .......polypropylene, 6" buttress
  • Battery capacity..............................................1250mA-hr
  • Suction screen.......................polypropylene, 420 micron

OPTIONAL PCB

  • Relay mode................................. selectable N.O or N.C.
  • Quiescent current:................................................. 32 uA
  • Slosh time delay:..............................................500 msec

OPTIONAL LINE POWER

  • Power cord.................................SJOOW jacket, 3 x14ga
  • Relay output............................................ 16A@277VAC

Some chemicals commonly used with these level alarms:

  • Aqueous Ammonia (conc.)
  • Aqueous solutions.
  • Chromic acid (50%, Rm. Temp)
  • Glycolic acid
  • Hydrochloric acid (conc.)
  • Nitric acid (30%)
  • Oils (including waste oils)
  • Potassium carbonate (40%)
  • Polyester resin (viscous)
  • Sodium hydroxide (50%)
  • Sulfuric acid
  • Sodium Hypochlorite

The following chemicals not compatible with the acrylic flowmeter:

  • Sulfuric Acid 98%
  • Lactic acid
  • Phosphoric acid

CLICK FOR CHEMICAL RESISTANCE CHART

INSTRUCTIONS: ILK-PP
INSTRUCTIONS: ILP-PP
INSTRUCTIONS: SILENCE BUTTON
INSTRUCTIONS - RELAY
_______________________________________________________________________________

Model ILP-PP

PP with liquid pipe and flowmeter
$269

Tubing connection size

Model ILK

No Feed Pipe

Material

Model ILPX

With liquid pipe, no flowmeter

Material
Tubing connection size

_______________________________________________________________________________
Relay Output with Cord
RelayOutput

$78
Slip-on Cap A regular IBC lid IBCLid

$29
Check Valve
Poppet5KB

Material

from $32
AC Power Cord When plug-in AC Tank alarm silence button

$36
Tank Vent Cap Vent cap installed
IMG0238
$12

CLICK TO ENLARGE
Different Buzzer Tones

Tone Type

Different Buzzer Tones
Buzzer Volume Control Snap-on "muffler" reduces
BuzzerMuffler
$5

Tank Alarm Remote Shutoff Box Mount on the
Remote Shutoff Box

CLICK TO ENLARGE
Wireless Transmitter & Receiver Wireless transmitter
Wireless Receiver for Tank Alarm
$175

Alternate Color LED
LED option for digital timer
$11

Color

PLC Output
DRUM ALARM WIRELESS

CLICK TO ENLARGE

Questions?

Phone 585-301-0970
email: peter@drumalarm.com

item8

hit counter

Engineering RedBall1 Gizmo INSTRUCTIONS: ILK-PP INSTRUCTIONS: ILP-PP INSTRUCTIONS: SILENCE BUTTON